New engine

[Feliks]

Drive for pump or oscillating dynamo:



Will it be possible the new World Energy Policy in line
with this map ??

http://www.new4stroke.com/Heightwave.PDF

Regards Andrew

[Feliks]

Well, who would have thought that Newcomen was so close to an adequate solution






Regards Andrew

[Feliks]

Beautiful simple new 4 stroke kinematics animation made at the
King Soud University.





And a little faster



Regards Andrew

[Feliks]

Well, who would have thought that Newcomen was so close to an adequate solution

I also very close to the Technology


Regards Andrew

[Feliks]

I think that this technology is very effective. Can you imagine that by doing the same movement up and down through the traditional piston-connecting rod-crankshaft to get the same ease the movement of this vehicle?
I think that it would then be much harder work. And these four , the looks on it, they not liked to work more than need....

Can you feel it ??

Regards Andrew

[The Dieselduck]

Looks pretty interesting Andrew. why the twin cylinders at the top, in the previous illustration, out of sync a bit. I imagine your firing in only one of those pistons, then, you are harness the pressure on the large piston and finally on the smaller one, a bit akin to the old triple expansion steam engines?

[Feliks]

Well, who would have thought that Newcomen was so close to an adequate solution

I also very close to the Technology


Regards Andrew

Thanks Martin.

However and that will had such a good humor, just take a timber and a little grease lubricated.

Do not need any oil !!

Seal or Teflon or lubricated with diesel fuel.

OIl = diesel fuel in this picture





Regards Andrew

[Feliks]

Some new4stroke history:

Print table of Fortran 1982 program.
I could choose from 100 of these tables, each for different angular positions of crakshafts.
Here is one of them:


Working drawing of the head:



Regards Andrew

[Feliks]

Reversing motors.

My Half rotate engine is still a very important attribute, with marine applications.

Namely, this is the type of engine Reversing motors, but with a very easy switching float back and forth. Just after stopping the engine, we'll rotate the crankshaft in the second rotate. The engine ignites easily and will work back.
In traditional designs, Eby worked in the back of the engine, it must be by special changers to switch cam shaft and injection pump shaft.
Half rotate enought rotate in other turn, and start.



The first windmills pumped water in America. To sustain this good tradition, I developed a little more modern sytem for the production of electric current in a similar way of pumping water.Whether American landscape views, are water sphere.I decided to add this view to the next shot where the water will be collected water so that it could give electrical energy when draining it back into the lower reservoir.




This water will be pumped sphery as in the first versions of windmills, wind.
The wind turbine will move a small diameter, but it is a multi-blade, placed together with the hydraulic pump in the middle of a specially constructed balloon. Balloon will be tethered, as previously barrage balloons.
Only that will go along the line, hydraulic pipes, the hydraulic motor, which will be driven water pump located in the lower reservoir.The water pump will continuously pump water to sphery. Now the water falling from the lower reservoir back to the shery, will do an electric current through hydrogenerator.






Every so water sphere about the capacity of 2000 m 3, and the height 100 m can give power 10 MW for 3 minutes. If filling pumps water with the one I believe loss is managing to fill waters up, we will have it 10 MW driven with wind turbine in balloons.
Of course, the balloons could be filled up by hydrogen, because today we have very good material on the shell.
This system could be installed in any place where electricity is needed, and thus would have limited losses on the transfer.
Also low noise, and the invisibility of the rotating blades, not to interfere in coexistence with the environment.Balloons can be affixed to a height of 150 to 200 meters, where the wind is always blowing on the ground even when there is absolute silence.

some links:
http://media.primezone.com/cache/189/int/8385.jpg

http://www.youtube.com/watch?v=mu2glpmR ... embedded#!

http://www.engadget.com/2010/06/21/nort ... endurance/

http://www.youtube.com/watch?v=W3n5cUaG ... r_embedded




Of course, two rotate in one direction and two in the opposite direction.
You must use a very light hydraulic oil. If it were not frozen in winter.
Hydraulic pump in the balloon has the best power to weight ratio. All the airlines are working on the hydraulic actuators.
Of course, all of the balloon must be tested in the wind tunnel aerodynamic, in order to fully match the efficiency of the 21st century

Regards Andrew

[Feliks]

Some pictures of how to create a balloon from the inside






and NASCAR wind tunnel




Regards Andrew

[Feliks]

There is a way to shorten a bit of flexible hydraulic tube...



Well, if it accidentally escaped gas from the balloon and so it can be



Regards Andrew

[Feliks]

Name : Jazz Big Band





Regards Andrew

[Feliks]

Rotating Dixieland Yoda.






Next Dixieland :




In some tubes can be hidden anti-missile ..

Regards Andrew

[Feliks]

A new way of sailing through a balloon which has the wind, and transmits energy to the propeller using hydraulics




And sailing version of the Venturi jets



Regards Andrew

[Feliks]

I simply will look as flat block. It can be cast as a single unit. It did not need the division on the block and head. Because the pistons can be put at the bottom......
It is full 4 stroke engine.








Regards Andrew