I leaned through the engineroom door to snap this shot showing the engine inclination. I wonder what the engine actually sees when the ship is pitching in rough weather.
Engine Inclination
- Merlyn
- Fleet Engineer
- Posts: 1024
- Joined: Wed Dec 25, 2013 7:19 am
- Currently located: South Coast UK
- Contact:
Re: Engine Inclination
I reckon that's a shot of your wrist watch engine. Hopefully it sees tight engine mounts holding down bolts in rough weather.
Remembering The Good Old days, when Chiefs stood watches and all Torque settings were F.T.
- JK
- Enduring Contributor
- Posts: 3066
- Joined: Tue Sep 04, 2007 2:29 am
- Currently located: East Coast, Canada
- Contact:
Re: Engine Inclination
I wasn't there to look at the engines specifically, but I glanced at them on the way by. They have what seems to be pretty substantial hold downs.
- The Dieselduck
- Administrator
- Posts: 4131
- Joined: Sun Jul 22, 2007 1:41 pm
- Currently located: Nanaimo, British Columbia, Canada (West Coast of Canada)
- Contact:
Re: Engine Inclination
Hey JK, What kind of engine is that?
On tugs with z drive, it's pretty common to see quite an angle, in particular, a FWD leanin angle. Not all OEM though have this in mind, like the C32 I'm working with these days, the drains are STD, for aft leaning engines, making for a slightly messier maintenance.
On tugs with z drive, it's pretty common to see quite an angle, in particular, a FWD leanin angle. Not all OEM though have this in mind, like the C32 I'm working with these days, the drains are STD, for aft leaning engines, making for a slightly messier maintenance.
Martin Leduc
Certified Marine Engineer and Webmaster
Martin's Marine Engineering Page
http://www.dieselduck.net
Certified Marine Engineer and Webmaster
Martin's Marine Engineering Page
http://www.dieselduck.net
- Merlyn
- Fleet Engineer
- Posts: 1024
- Joined: Wed Dec 25, 2013 7:19 am
- Currently located: South Coast UK
- Contact:
Re: Engine Inclination
It's a wrist watch engine DD. I have seen installations where the flywheels faces forward thro angled drives and engines up against the transom.
Remembering The Good Old days, when Chiefs stood watches and all Torque settings were F.T.
- Merlyn
- Fleet Engineer
- Posts: 1024
- Joined: Wed Dec 25, 2013 7:19 am
- Currently located: South Coast UK
- Contact:
Re: Engine Inclination
You must have heavy smokers down below looking at the big air cleaner ?
Remembering The Good Old days, when Chiefs stood watches and all Torque settings were F.T.
- JK
- Enduring Contributor
- Posts: 3066
- Joined: Tue Sep 04, 2007 2:29 am
- Currently located: East Coast, Canada
- Contact:
Re: Engine Inclination
MTUs , Martin. Highly skewed props. When I get a chance I'll have to see if I got a picture of them or can get one.
I'm not fussy on those smaller, go fast ships. I have thrown up quite enough on them when I was starting out many years ago.
High speed, high power engines Merlyn. They exhaust through the stern not up a funnel. Noisy buggers.
I'm not fussy on those smaller, go fast ships. I have thrown up quite enough on them when I was starting out many years ago.
High speed, high power engines Merlyn. They exhaust through the stern not up a funnel. Noisy buggers.
- The Dieselduck
- Administrator
- Posts: 4131
- Joined: Sun Jul 22, 2007 1:41 pm
- Currently located: Nanaimo, British Columbia, Canada (West Coast of Canada)
- Contact:
Re: Engine Inclination
Ho I did not recognized the MTU without the 20 turbos in the picture. ehehehe
Martin Leduc
Certified Marine Engineer and Webmaster
Martin's Marine Engineering Page
http://www.dieselduck.net
Certified Marine Engineer and Webmaster
Martin's Marine Engineering Page
http://www.dieselduck.net
- Merlyn
- Fleet Engineer
- Posts: 1024
- Joined: Wed Dec 25, 2013 7:19 am
- Currently located: South Coast UK
- Contact:
Re: Engine Inclination
R R I believe again? We have them over here driving water squirters , screamers jobby. We have some engines over here that will run Upside Down ( without seizing ) ? On a rollover? Makes anyone? Now that's an inclination and a half.
Remembering The Good Old days, when Chiefs stood watches and all Torque settings were F.T.