New engine

General maritime and engineering discussion occurs on this board. Feel free to post newsbits, comments, ask questions about maritime matters and post your opinions.
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

I find a beautiful array :

Image
At last something happens .

In my oscillating dynamo I help cellular telephone IC Lm 2621.
May be cellular telephone need advanced mechanic?? :idea:

If put in cellular telephone mechanic automatic movement,using in mechanic clock, and miniature electric generator drive it, we don't need charge cellular telephone.Phone will be loaded on our result of traffic, obvious as there will be in our pocket

Some parts and principle work of automatic movement:

Image

Image

Image

Image

Image

Perhaps, we must use e.g. 6 such systems, in order to can be charge phone goods .?
Same philosophy : no one big , many little.
May be Swiss precision it will astonish again .;)

My propose for yacht: On highest point of mast instead of flag,for example,box belongs to place with such array: 20 pcs X 20 pcs X 60 pcs systems (50 cm x 50cm x 30 cm). All 24000 system's. And I think, so enough for made electric energy for yacht. Without any fuel.

There is possible build closest house fiberglass mast too and we insert dynamo in this highest place. When wind blows this e.g 15 meter mast too have some movement.
Without barrier for birds , and no sound effect. And looks better :wink:

Andrew :D :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

My friend ( architect and musician) has said that it distrusts springs." Because if it can crack, then sometime it will crack sure." I agre with his think:


Image




And my vision Pack of oscillating dynamo:



Image



Regards Andrew :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

Why I don't like spring:
Yes, discus about advantages and disadvantages of spring a re start
Some video, what spring of poped can make :-)

http://www.engr.colostate.edu/high_spee ... 000fps.wmv

http://www.engr.colostate.edu/high_spee ... 000fps.wmv

http://www.engr.colostate.edu/high_spee ... 000fps.wmv

I thik, so pistons valve , and rod eliminate this "play sprig".
Mass too is better solutions.

Regards Andrew :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

Farthest development at one pivot stand differential animations, but this time about 180 degrees removed rod. Permutation is possible about 90 degrees definitely too.My be It's help if torque will not have a linear relationship But which setup will be better, as yet, I do not know
To develop simile Torsen torque biasing and traction management too.

Image


You see this animations?


Image

Andrew :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

You know last time my distaste for transmission cogged ??
Visit Ricardo Company -http://www.ricardo.com/engineeringservi ... ngineering I see many problem with it.

My solve: Wind motion my oscillating dynamo packs, without any cogged transmission:


Image






But if you no like oscillating dynamo , I have my proposes without this:
Name Beam Dynamo.


Image




Image



Image




Image



Such type of pump has been born for too, that produce electric current from marine waves can .
Under-sea fields with energy?


Regards Andrew :D :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

A nice post-application for oil-pump after the derricks will be completely dried up !

And then, it will be possible to buy all for symbolic dollar it.


In Beam Dynamo we can change input data using set off pulles.

This pull my story:You know last time my distaste for transmission cogged ??


Image


First principle pulles:

Image


Regards Andrew :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

Big Boy with Stephenson Second engine are going.

Image
Ride it where ?


ps Need new electronic valave drive system.


Advantages of half rotate pumps are additional possible regulations.
In normal piston pump, we have two elements definition pumps – diameter of piston and stroke piston In half rotate pump we have too same elements: diameter “piston” and long “piston” and additional important possible regulations TORQUE of drive pump on arm with some hole...
This regulation are without additional gear .
For salt water I think better solution made aal this pump PCW , or ABS, or propose - ceramic

Image


Regards Andrew :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

My grandfather worked as engineer on railroad .......
Unfortunately, it has died before I have been born ..


Image



What is this?

Image


This is a hydraulic pump of widmill :bowtie:

Manner of utilization is next my proposal instead of mechanical transmission
in producing windmills electric current :Hallf Rotete Pump
Main principle of operation on following drawing and has enclosed animation
Solution has many advantages from haf rotate pump. Expensive
substitute is first most important and noisy, emergency transmission
of mechanical windmill .
It is presented next advantage on former drawing
for one dynamo driven manner of connection
of whole farm of windmill hydraulic engine serious too.
This way, we save several most expensive elements of windmills,
treating such farm windmill as integrity .( Complex design)

Image

Regards Andrew Santa Claus :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

Star engines were characterized biggest always force density.


Image

Happy New Year Andrew :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

Opposite too RB211 engine:

60 „cylinder” star half rotate engine parameters:
Diesel engine, sum 250-liter work volume, 4000 RPM,

20 000 KW, 170 g/KWh.--- 5,8 KW/ KG, full power: 3,5 Ton /h

250 L / 15 =16 liter work /4 cylinder x 2 = ~~ 32 liter full cylinder volume dimmer

long cylinder about 300 mm .(3 dcm), 32 / 3 = 10,5 dcm^2 S cylinder

10,5 / 3, 14 = 3,34 (r^2) r = sqrt 3,34 =1,8 dcm (180 mm) d cylinder = 360 mm

Sum D = 900 mm , long =1200 mm, d cylinder = 360 mm
V all engine = 4,5 x 4,5 =20,25 x 3,14 =53,5 (S dcm) x 12 =642 dcm^3

All weight (aluminum) 642 liter –250 liter =392 liter x 3,5 KG =1372 KG ( 1,37 Ton max weight) ~ ~ ~ ~ 2 Tones weight. . And birds no afraid :)

Image

Image


Regards Andrew :D :D

P.s. If you need next 60 cylinders in left side ?? ; :)
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

In my latest solving the oscillatory dynamo, a diode who exchanged the changeable oscillatory electricity for the electricity about the permanent polarity was crucial element
Such an element fulfilling identical functions as the diode exists in the hydraulics of theses. There is a valve one-sidedly letting it in to water. it is opening for example only then when the pressure from the feeding side exceeds certain described by the threshold e.g. 10 bars. When the pressure is on the feeding side it is smaller, the valve is closing it oneself. and doesn't allow for moving back waters.

The principles of operation are the same like at pumping the bicycle wheel up with pump, but will refer to water. In this way we can hold. in the pipeline pressure e.g. 10 bars, and from leaking out of the pipeline who will be above the pump e.g. 100 meters will be sailing out water.
The one straight line I decided to use the principle for the production of the electric current with the help of sea waves. Although he is supposed to produce the electricity, it is being imported these are for inflating the problem waters sea into the container with water sea e.g. to height 100 of meters, or similar (e.g. on high cliff seashore). The rest is known and professionally made as the normal power station aqueous, but in this case she will be to sea brine. isn't buying it special one should actually solve the difference, only a matter of the precipitated corrosion .


Particularly that such a very similar solution was already on an island applied Okinawa, in the version of the power station pumped storage (but pumping into the container with the help of the electric energy- classic pumped storage).

Into my to pump the version this brine there will be sea waves driving water pumps with valves with diodes into the container Leaking in water only in direction of the container. pipes from pumps into the container will also have middle diameter, in order to in the time of whom from valves, not to waste the energy from different good pumps. Unfortunately the number can reach such pipes even 1000, at the productivity every e.g. 1 m^ 3 / sec.
But by it we can get the power of such a power station 1000 of the MW .

Costs of making such a power station will also be smaller, since for her devices won't have to pump water into the container how it is in classical power stations of this type. Machines will be so like by a normal hydroelectric power plant straight lines and no high cost.

http://www.new4stroke.com/salt%20water% ... torage.pdf

Image

Also shortened descriptions Polish pumped - storage to slight differences of the water levels (100 m) is describing http://www.pistonheads.com/gassing/topi ... 7463&i=260 or
http://www.new4stroke.com/plants.pdf


Gross from many centuries of coasts England and Ireland they were attacked by marine waves .
People built obstacle for these waves sometimes, that they did not prevent from life on islands.
I think that would end this immemorial war goods , and invite this ocean on coast, but that it is high, it belongs it help. It belongs to take advantage it waves, in order to they pumped on its high coast of water.
I think, so around England , Ireland , North America ,shall made this power plant.
More belongs to place in ocean for water pomp e.g.

Pistons type , or my idea half rotate, which will drive usual floats clinched for they behind assistance of rope. Ordinary belongs to place behind each pump bolts, which will be opened e.g. at 10 kG/cm2 (Acting similar for diode I my oscillating dynamo) and which for collect tubes for reservoir on high coast miss water drive it.
Collecting tube should for example for flow 1 m3/sec 0,6 m have diameter.

Image

Image
Image

For achievement in such this collecting tube of flow 1 m3/sec and 10 bar , requirement 12 pump wanted for transport water on according to following specification 100 m height too reservoir.

Pump reconciles, for simplification about normal piston, should have 0,6 m diameter, and 3 m of height. During average jump of rippling 2 m, it will give during one cycle for composite tube 0,5 m3 water pushed (S= 28 dcm2 H= 20 dcm (2 meter) = 560 dcm3 (liter). For set up flow 1 m3, TWO such pumps should pump for collecting tube.
For proper fabrication of pressure on exit of pump ( set up 10 bar ), wanted proper swimmer is.
There is simple account surface of piston of pump will together page (S) x 100 surface of swimmer.
In my example, surface of piston of pump it 28 dcm2, it signifies that swimmer)should have 2800 dcm2. In order to swimmer had such surfaces, it must have 20 m diameter, and definitely 1 m of height. It needs one kit about 12 pumps 12 swimmers 20 m each diameter, or about dimension one swimmer 12 x28 m2= 336 m2.

For behavior some reasonable spans, it is possible to accept, that for such array for production capacity 1 m3/sec 10 bar, wanted near 700 m2 place rippling sea .

Need for continuous supplying tank for power station theoretically 700 m3/s (716 MW , 100 m height ) requirement 700 x 700m2 = 490000 m2 rippling sea . It is theoretically only 700 m x 700 m !, when 2 m average heights of waves.


Here, mathematical enumeration same only:

To 1m3/ sec
1 m^3/sec 10 bar(H=100m ), 600 mm diameter pipe and piston pump, S= 28 dcm2 Hwave= 20 dcm (2 meter) = 560 dcm3 (litre) for 1 m3 need 2 piece . but period are 6 sec , sum 6x 2 = 12 piece pump .

S pump= 28 dcm2 , 10 bar, F =28 T, Hfloat >1m, S float ~~=2800 dcm2 (28 m2) , D float =~~20m
12 piece x28m2 =336 m2 ~~ =100m x 7m using area =700 m2

700 MW (700 m3/sec), H=100m
700 m2 x 700 = 350000 m2 . ~~700m x 700m area of wave



As elements are presented from marine waves over system production current professional , they are built in the world already and test, additional requirement of experience for their building not.
Another, very important information in relation to the system. System the one should be only as storage, rather than storage-pumped what significantly the height of investments will lower in comparing to current answers. Costs will only be so like for an ordinary hydroelectric power plant
Only water pumps with valves (diode) can so that touch up still and selected materials. but in general, it is piston pump known for the antiquity. Summing up, mechanical problems are solved, and with the appropriate swing one should only build such a power station.
The degree of the safety of such containers will also be very high, since put very close the sea, in case of the breakdown of unsealing, they won't cause heavy losses, since water quickly will find its way back to the sea.

I think that wonderful geographical conditions will permit on high cliff Scotland England and Ireland, to build such containers into whom sea, highest waves will be pumping brine on average in world a lot. it means that the efficiency of such a system will be most effective in world, and therefore built containers should be around these countries what in the future can guarantee the green energy for all countries Europium.

Regards Andrew :)
User avatar
The Dieselduck
Administrator
Posts: 4131
Joined: Sun Jul 22, 2007 1:41 pm
Currently located: Nanaimo, British Columbia, Canada (West Coast of Canada)
Contact:

Re: New engine

Post by The Dieselduck »

I was just browsing the website of Eco Motor, which has a very interesting engine on the drawing board, and some pretty heavy names associated with it (Cummins, Volkswagen etc), have a look see at http://www.ecomotors-intl.com/ if your are into that kind of thing.
Attachments
OPOC engine from Eco Motors
OPOC engine from Eco Motors
OPOC.jpg (116.5 KiB) Viewed 118140 times
Martin Leduc
Certified Marine Engineer and Webmaster
Martin's Marine Engineering Page
http://www.dieselduck.net
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

The Dieselduck wrote:I was just browsing the website of Eco Motor, which has a very interesting engine on the drawing board, and some pretty heavy names associated with it (Cummins, Volkswagen etc), have a look see at http://www.ecomotors-intl.com/ if your are into that kind of thing.
The thanks Dieselduck for the beautiful link and animated films !

I this I used the similar mechanical layout to my four stroke :

Image

Perhaps even this version will win ? ? :D

Best Regards Andrew :D :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

Above I described power stations to Zarnowiec about the power of 720 megawatts, and the size of her upper container

But this size of the container will suffice for the cycle 5.5 an hour long, that is through 5.5 hour we can receive 720 megawatts of the power. But if the productivity of pumped sea water is sufficient, for keeping the fluidity of the move cycle 2 hour will be enough for us an hour long.
Then about such a size we can obtain 2000 MW from the container .A by supporting the stormy weather even 4000 MW, if installed devices will let it.

On shallow water it is necessary to use half- rotate of the pump .

In of Ewas to Żarnowiec at present the employed is 114 - here with it:
three members of the management board,
29 engineering-technical employees,
59 paid housemen hourly,
9 economic employees,
10 administrative attendants.

Andrew :D :D
Feliks
Superintendent
Posts: 434
Joined: Sat Jan 05, 2008 4:45 pm
Currently located: Kraków,Polska
Contact:

Re: New engine

Post by Feliks »

Interesting n engine Grek Inventor:http://www.pattakon.com/pre/index.html

Regards Andrew :D
Post Reply