2nd class technical drawing

Going through the licensing process ? Have queries, comments, or do you need an answer to that obscure exam question ? This is the place to post.
Ajay
Tanktop Cleaner
Posts: 14
Joined: Tue Dec 03, 2013 11:15 pm

2nd class technical drawing

Postby Ajay » Sat Mar 21, 2015 10:40 pm

Dear seniors,

I am preparing to write 2nd class Technical drawing exam. Can anyone here guide me which institute in canada prepare for this exam?
Also where can i get previous year transport canada examination papers ( EK Motor, EK General)
I am a 2 class engineer from India, and a landed immigrant in Canada, preparing to convert my license to Canada . I am not familiar with the colleges here. Your suggestions are highly appreciated and will be a great help. Thanks
Ajay.

User avatar
JollyJack
Fleet Engineer
Posts: 1125
Joined: Wed Mar 24, 2010 3:57 am
Currently located: Eastern Canada

Re: 2nd class technical drawing

Postby JollyJack » Sun Mar 22, 2015 8:17 pm

Where are you Ajay? It's a big country.
Discourage incest, ban country "music".

Ajay
Tanktop Cleaner
Posts: 14
Joined: Tue Dec 03, 2013 11:15 pm

Re: 2nd class technical drawing

Postby Ajay » Wed Mar 25, 2015 2:59 pm

Hi Jolly Jack ,

I am in Calgary, AB

User avatar
JollyJack
Fleet Engineer
Posts: 1125
Joined: Wed Mar 24, 2010 3:57 am
Currently located: Eastern Canada

Re: 2nd class technical drawing

Postby JollyJack » Wed Mar 25, 2015 7:17 pm

Best thing I can suggest is to get hold of a drawing table, paper and instruments (T square, 45 and 60/30 set squares, compasses etc) and Reeds Engineering Drawing for Marine Engineers. Work through that then go challenge the exam. It's 6 hours, and is scheduled on Fridays.

Have you gone through the Direct Entry process with Ottawa?
Discourage incest, ban country "music".

Ajay
Tanktop Cleaner
Posts: 14
Joined: Tue Dec 03, 2013 11:15 pm

Re: 2nd class technical drawing

Postby Ajay » Wed Mar 25, 2015 9:21 pm

I have done all the drawing in reeds engineering drawing, but that was back in college 15 years ago ! Never had to touch that again since the time I passed ! Now I cant make it alone ..! Need some guidance..plz let me know if anyone have an Idea about any college . Thanks

Yes , I have gone through Direct entry process

User avatar
JollyJack
Fleet Engineer
Posts: 1125
Joined: Wed Mar 24, 2010 3:57 am
Currently located: Eastern Canada

Re: 2nd class technical drawing

Postby JollyJack » Thu Mar 26, 2015 7:09 pm

SAIT in Calgary should have a technical drawing course of some kind. Your nearest TCMS office is in Edmonton for the exam. It's really just a matter of practice.
Discourage incest, ban country "music".

EL
Mechanic
Posts: 68
Joined: Sun Sep 16, 2007 4:06 pm

Re: 2nd class technical drawing

Postby EL » Thu Mar 23, 2017 3:45 pm

Does anyone did this exam recently? What size paper was used, which drawing tools were you using?

User avatar
JollyJack
Fleet Engineer
Posts: 1125
Joined: Wed Mar 24, 2010 3:57 am
Currently located: Eastern Canada

Re: 2nd class technical drawing

Postby JollyJack » Fri Mar 24, 2017 8:39 am

The standard drawing sheet is supplied, as are all the instruments. T Square, 2 set squares, 30/60 and 45/45, compasses, scale rules, pencils, erasers, pens, templates etc. You can bring your own, of course, you'll need a calculator anyway. (Or slide rule if you prefer) You have 6 hours on a Friday to do it.
Discourage incest, ban country "music".


Return to “Training Room”

Who is online

Users browsing this forum: No registered users and 1 guest