westfalia Purifier Problem
Re: westfalia Purifier Problem
Hello my name is rian, i have gea purifier too type osd 5 , i have a problem that bowl cannot discharge and open , purifier bowl completed check and all o rings were replaced, water block strainer was cleaned too , manually overides the solenoid valves but still no any sound of discharging , any advice to solve the problem? Thx you
Re: westfalia Purifier Problem
Good day.
My name is Michael please i need assistance with the present issue i am experiencing on the Westfalia DO Separator OSE 5-91-037_4. After the starting circle have been completed and purifier attained the required speed, purification starts and fuel oil start discharging but the "Clean fuel discharge pressure still reads 0.0bar" after some few minutes, it brings alarm on the displace screen (PAL 1 Clean oil discharge , please check valve setting V7).
Please what will i do to rectify this present issue.
My name is Michael please i need assistance with the present issue i am experiencing on the Westfalia DO Separator OSE 5-91-037_4. After the starting circle have been completed and purifier attained the required speed, purification starts and fuel oil start discharging but the "Clean fuel discharge pressure still reads 0.0bar" after some few minutes, it brings alarm on the displace screen (PAL 1 Clean oil discharge , please check valve setting V7).
Please what will i do to rectify this present issue.
- Attachments
-
Re: westfalia Purifier Problem
Hello Michael. Have you tried all of the following?
From the manual.
**********Text displaying #44 for PAL 1 (pressure low)
Clean oil discharge valve (product discharge valve) V7 open too wide - Check valve position.
Feed capacity reduced - Check feed capacity. Try increasing the throughput.
Set point of PT1 set too high. Check set point.
Water pressure for hydraulics during water closing pulse T06 too high, bowl has opened. - Check T06.
Feed pump failure - check feed pump.
Feed pump speed low - check frequency converter.
Feed valve V1 in recirculation position - check V1
Overflow to water side - check filling water volume.
Pump running wrong way - check rotation.
Bowl gaskets leak - Check gaskets; replace if necessary.
Alarm delay T07 too short - check setting.
Alarm bridging T11 too short - check setting.*********
Good luck, John
From the manual.
**********Text displaying #44 for PAL 1 (pressure low)
Clean oil discharge valve (product discharge valve) V7 open too wide - Check valve position.
Feed capacity reduced - Check feed capacity. Try increasing the throughput.
Set point of PT1 set too high. Check set point.
Water pressure for hydraulics during water closing pulse T06 too high, bowl has opened. - Check T06.
Feed pump failure - check feed pump.
Feed pump speed low - check frequency converter.
Feed valve V1 in recirculation position - check V1
Overflow to water side - check filling water volume.
Pump running wrong way - check rotation.
Bowl gaskets leak - Check gaskets; replace if necessary.
Alarm delay T07 too short - check setting.
Alarm bridging T11 too short - check setting.*********
Good luck, John
Re: westfalia Purifier Problem
Hello
I am vikas,I am 4/E of chemical tanker,I have same problem with my L.O purifier and the model is westfalia GEA OSD 591067.
After starting the purifier after 15-20min, the purifier will be stopped showing in panel "PAL1 CLEAN OIL DISCHARGE.
valve setting v7/feed capacity setting pt1 for PAL/water pressure for opened valve v3/timer06/t07alarm delay/quantity of water/bowl not sealed.
We are checked and tried out everything.
I am vikas,I am 4/E of chemical tanker,I have same problem with my L.O purifier and the model is westfalia GEA OSD 591067.
After starting the purifier after 15-20min, the purifier will be stopped showing in panel "PAL1 CLEAN OIL DISCHARGE.
valve setting v7/feed capacity setting pt1 for PAL/water pressure for opened valve v3/timer06/t07alarm delay/quantity of water/bowl not sealed.
We are checked and tried out everything.
-
amir_master19891368
- Bilge Dweller
- Posts: 5
- Joined: Tue Oct 05, 2021 2:14 am
- Currently located: ship
Re: westfalia Purifier Problem
Hello
My name is Amir and I have LO purifier westfalia osd20
For ME Lub Oil sump and when the purifier is run, water in oil for ME Lub Oil increases without any alarm. How can I fix the problem??
Please advise, I am under a lot of tension. Thank you.
My name is Amir and I have LO purifier westfalia osd20
For ME Lub Oil sump and when the purifier is run, water in oil for ME Lub Oil increases without any alarm. How can I fix the problem??
Please advise, I am under a lot of tension. Thank you.
Re: westfalia Purifier Problem
How do you know that the water in oil is increasing? Is the water sensor on the engine lubrication system showing the water level? What is the level of water before and after the purifier is run? Is the purifier putting water in the oil? Is the water sensor on the purifier working correctly?